Connect with FloraCraft → Connect with FloraCraft at Facebook Connect with FloraCraft on TwitterFollow FloraCraft on Pinterest

Hanging Flower Cans

Browe Project Categories
| More

Supplies

FloraCraft® :
Design It:® Silks & Naturals®, Desert Foam® Mug Plugs, 2 5/8″ x 3 3/4″,  two
Design It:® SimpleStyle® Wired Burlap Ribbon, 2 1/2″ wide x 24″ length, natural
Design It:®
Floral Shears
Wire Cutter
Make It: Fun® Foam Cutter

Design Master®:
-Primer
-ColorTool® spray color: White, Yellow, Fuchsia Bright

3 1/2″ diameter x 6″ tall (approx.) empty soup cans, two
Chevron grosgrain ribbon, 5/8″ wide x 1 1/3 yds. of each: Fuchsia and Yellow
Gerber Daisies, 4″ diameter, two of each: Fuchsia and Yellow
Yellow Forsythia, 1 branch
Fuchsia small wild Daisy, 1 branch
Aleene’s®: (iLoveToCreate®)
– Turbo Tacky Glue®
– Max Tacky Adhesive™ Glue Stick
Misc.: Old newspapers, large cardboard box (for spraying), wood pencil (full length), ruler, large crochet needle, transparent tape, hammer, large nail, screwdriver

Instructions

  1. Thoroughly clean soup cans of all labels and glue – wash with soapy water and dry. In well-ventilated, newspaper-covered area (inside box) spray each can with two coats of each in the following order, drying in between: primer, white, and either yellow or fuchsia. Let dry.
  2. Measure and mark bottom center (outside) of one can. Using a hammer and large nail, pound a hole in can on mark. Carefully work nail around to expand hole large enough for pencil to fit. (Check that pencil fits.) Apply Turbo Tacky glue to bottom of Foam Mug Plug and insert down into can. Let dry. Repeat with other can.
  3. Insert pencil through hole in bottom of can with one hand, while holding Mug Plug in place inside (since pressure will be great.) Push pencil all the way through can and Mug Plug, being careful to go straight up so that hole on top of Mug Plug is still centered. Remove pencil. Repeat with other can.
  4. Use Floral Shears to cut 1 yd. length of each chevron ribbon. (Use opposite colors on cans.) Tape end of ribbon to crochet needle and feed through hole of can/Mug Plug. Tie overhand knot 3″ up from bottom end, leaving a tail. Repeat with other can.
  5. Cut 12″ length Burlap Ribbon and apply glue stick to one side. Press against middle of can with ends slightly overlapping on back. (Trim as needed and use glue stick to hold.) Cut and glue 12″ length chevron ribbon around middle of burlap ribbon, slightly overlapping on back. (Use same color ribbon as hanger ribbon.)  Repeat with other can.
  6. Use Wire Cutter to cut apart flower stems. Insert small yellow and fuchsia flower in opposite color cans. Then insert same color larger daisies into each can.
  7. Align top ends of ribbon and tie together using strong overhand knot. Hang over separate pegs, with cans different heights.

 

SOURCES

FloraCraft®
(800) 253-0409
One Longfellow Place
Ludington, MI 49431
www.floracraft.com

Design Master®
(303) 443-5214
P.O. Box 601
Boulder, CO 80306
www.dmcolor.com

iLoveToCreate®
A Duncan Enterprises Company
(800) 438-6226
5673 East Shields Ave.
Fresno, CA 93727
www.ilovetocreate.com

Post a Comment

Your email is never shared. Required fields are marked *

*
*